Leading 10 common forklift accidents ， forklift operation should take note of these matters ！.

Leading 10 common forklift accidents ， forklift operation should take note of these matters ！.

Blog Article

Do not underestimate the forklift at the office. If the procedure is bad, there will certainly be significant accidents in minutes, and there are many accidents involving forklifts.

Situation 1: The forklift freight obstructed the vehicle driver's view, and the individual in front might not be found, causing a rolling crash.
Instance 2: In order to keep the equilibrium of the forklift when raising heavy products, the workers used their body weight as the counterweight, which almost caused casualties.
Instance 3: The size of the forklift freight surpasses the allowable width of the course and holds on the roadside shelf, which practically causes an accident.
Instance 4: Forklift is speeding up and rolls over during a turn.
Instance 5: The forklift vehicle driver did not observe the pedestrian, and the pedestrian did not observe the forklift.
Case 6: The forklift lifts the employees unlawfully, the forklift chauffeur does not use the safety belt, the forklift lifter falls and the driver is squashed when the forklift rolls over.
Case 7: The forklift vehicle driver did not use a seat belt and fell from the lorry when it rolled over and was crushed.
Forklift procedure ought to take note of these issues ：.

Begin.
1. Before beginning, observe the surroundings, and after validating that there are no challenges that hinder the safety and security of driving, honk the horn initially and after that begin.
2. For automobiles with hydraulic (air pressure) brakes, the brake hydraulic stress (air pressure) scale must be secure before beginning.
3. When the forklift starts with a tons, the driver must first verify that the load is steady and dependable.
4. The beginning should be slow-moving and stable.

Driving.
1. When driving, the elevation in between the bottom end of the fork and the ground ought to be maintained 300mm-400mm, and the mast must be slanted backwards. .
2. Do not raise the fork too high when driving. When entering and leaving the job website or while driving, beware that there will certainly be no obstacles in the sky. When the tons is taking a trip, the fork should not be increased expensive, which will impact the security of the forklift. .
3. After unloading, the fork ought to be reduced to the regular driving position before driving. .
4. When transforming, if there are pedestrians or lorries nearby, the driving signal ought to be provided initially. High-speed doglegs are prohibited. High-speed sharp turns will certainly create the lorry to lose lateral stability and tip over. .
5. When the forklift is downhill, it is purely restricted to switch off the fire and slide, and it is forbidden to brake all of a sudden while driving with tons unless there are unique conditions.
6. When the forklift is running, it must obey the web traffic rules in the factory and have to maintain a particular safety range from the vehicle in front. .
7. When the forklift is running, the tons should remain in the most affordable placement that does not prevent the driving, and the gantry needs to be properly slanted back. The lots will not be elevated other than when piling or packing. .
8. The height of the load should not block the driver's sight. In unique conditions, when the thing influences the forward vision, drive at a reduced speed when reversing.
9. It is forbidden to activate the ramp, neither to drive throughout the ramp. .
10. The risk-free driving speed of the forklift in the manufacturing facility location is 5 km/h, and it needs to drive safely at a low speed when getting in the manufacturing workshop area. .
11. When the forklift is lifted, raised or driven, it is restricted for workers to stand on the fork to hold items and play a stabilizing function. .
12. If issues are found, they will be repaired and reported in a timely way, and they will never run with health problems or hide them.

filling and dumping.
1. When fork-loading products, the distance in between the two forks should be adjusted as required to make the load of both forks balanced and not skewed, and one side of the product ought to be against the shelf. .
2. It is forbidden to deal with a single fork or use a fork top or draw. In special circumstances, safety and security warning signs must be established to remind bordering pedestrians. .
3. In the process of packing and unloading things, the forklift needs to be braked with the brake. .
4. The rate of the vehicle must be slow and consistent. Be careful not to roll the wheels on the dunnage, so as not to extend the rolled objects and harm individuals. .
5. When using a fork to fork the goods, the fork needs to be as deep as possible under the lots, and it should be kept in mind that the fork tip must not touch various other goods or things. The load ought to be maintained with minimal back tilt of the gantry to make sure that the load does not move in reverse. The mast can be tilted ahead a little when the load is reduced to permit easy placement of the tons and extraction of the forks. .
6. It is restricted to fork goods at high speed and hit tough objects with the fork head. .
7. When the forklift is working, it is prohibited for individuals to loaf the fork, so as to avoid the collapse of the goods and harm individuals. .
8. Straining is prohibited, and it is restricted to utilize forks to raise employees to engage in high-altitude operations to prevent high-altitude falling mishaps. .
9. It is not permitted to make use of the brake inertia to slide, place, round or roll objects. .
10. It is not allowed to use forks to choose, turn pallet discharge.

Leaving .
1. It is prohibited to leave the forklift when the products on the fork impend. Prior to leaving the forklift, you have to dump the goods or reduced the fork framework.
2. Draw the hand brake take care of to dead or dispirit the hand brake button.
3. The engine is switched off and the power is removed. (Except for unique scenarios, such as the vehicle driver does not leave the lorry's view and does not go beyond 1 min).
4. Eliminate the secret. .

Forklift Operation Precautions.
1. Prior to and after the forklift procedure, the look must be examined, and gas, lubing oil and cooling water ought to be added.
2. Check the safety performance of beginning, running and stopping.
3. Inspect whether the lights and horn signals are complete and effective.
4. Throughout the procedure of the forklift, inspect whether the pressure and temperature are regular.
5. After the forklift is running, the outside leakage ought to also be examined and the seals must be replaced in time.

Forklift Safety Operation Specifications.
1. You must examine prior to leaving the cars and truck;.
2. When you come across someone before you throughout driving, you ought to send a signal at a distance of 5 m;.
3. The driving rate in the factory does not go beyond 5 km/h;.
4. When driving, the nadir of the cargo need to be 0.3 m ~ 0.4 m in the air;.
5. The turning need to not be as well sharp to prevent the propensity of " totally free switching";.
6. Running up and down the incline must be slow and consistent, and no turning on the incline is enabled.
7. Do not drive throughout the gradient. When the slope is higher than 10%, the vehicle must be driven backwards when declining;.
8. When the forklift personnel lug the goods and move forward, if they come across large or hefty goods and most likely to the driver's line of vision, they should take the reversing workout
.
The "Eight Stand-on Electric Pallet Stacker Prohibitions" should be adhered to in the operation.
1. Single fork procedure is not allowed.
2. It is not enabled to raise the goods for long distance driving.
3. It is not enabled to grab the goods by turning over the pallet with the fork.
4. It is not enabled to straight shovel chemicals, flammables and other harmful chemicals with forks.
5. It is not permitted to use inertia force to grab the goods.
6. It is not allowed to utilize stopping pressure to expatriation round or easy-to-roll objects.
7. It is not enabled to bring individuals to work on the pallet or fork, and it is strictly prohibited to stand under the fork after the fork is elevated.
8. Do not drive side to side on slopes
.
Auto parking is not allowed under the list below conditions.
1. Curves, narrow roads, Stand-on Electric Pallet Stacker train crossings;.
2. Areas with a longitudinal incline greater than 5%.
3. When there is an obstacle on one side of the road, the opposite side of the section with the exact same size as the barrier should be within 20 meters at each end.

Web：https://www.onenforklifts.com/
Email：[email protected]
Phone：+86 13827083844